Visited product

915Mhz ArduFlyer2.5.2 UAV System with Protection AntiVibration Dome

915Mhz ArduFlyer2.5.2 UAV System with Protection AntiVibration Dome

Price: $149.99

Item: UAV-PLUS915

Weight: 300g

Off the shelf

915Mhz ArduFlyer2.5.2 UAV System with Protection AntiVibration Dome


APM 2.5 Hardware ArduPilot Firmware Rctimer ArduFlyer Tutorials & Discussion:

ArduFlyer Tutorials & Discussion



By Jabram:

Part 1 - Unpacking Rctimer ArduFlyer 2.5 kit(s) and making it work

ArduFlyer making it work, Part 1

Part 2 - Unpacking Rctimer ArduFlyer 2.5 kit(s) and making it work

ArduFlyer making it work, Part 2


The ArduFlyer is a complete open source autopilot system. Its design come from 3DRobotics and it 100% compatible with APM2.5.2. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. This version comes with the RC/Servo connectors unsoldered, so you can choose between straight or right-angled ones, both of which are included.



Arduino and ArduPilot Mega 2.5.2 Compatible!

Includes both right angle and straight pins for I/O, allowing user to customize as needed.

Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer

Onboard 16Mbit Dataflash chip for automatic datalogging

Digital compass powered by HMC5883L chip, included on the main board.

Invensense's 6 DoF Accelerometer/Gyro MPU-6000.

Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties.

Atmel's ATMEGA2560-16AU and ATMEGA32U-2 chips for processing and usb functions respectively.

The RCTimer Radio telemetry system base on 3DR Radio system and 100% compatible.

It's designed as an open source Xbee replacement radio set, offering a lower price, longer range (approx one mile) and superior performance to Xbee radios. It’s available in 915Mhz ; and in the following configurations:  serial board (for the air) and USB (for the ground).

The system provides a full-duplex link  using HopeRF's HM-TRP modules running custom, open source firmware.  Interface to the module is via standard 5V-tolerant TTL serial / FTDI USB serial.

Firmware upgrades and configuration are fully supported in the APM Mission Planner. Configuration is also possible through the 3DR Radio configurator and AT commands.



GPS Features and Specifications:

u-blox UBX-G6010-ST

5 Hz update rate

25 x 25 x 2 mm ceramic patch antenna

LNA and SAW filter

Rechargeable 3V lithium backup battery

Low noise 3.3V regulator

I2C EEPROM for configuration storage

GPS Power and Fix indicator LED

40.64 x 66.42 x 7.8 mm total size, 12.4 grams

Mounting hole diameter: 3.3mm

Mounting hole installation position 61.09 x 35.31mm


HMC5883L Magnetometer

ArduFlyer/APM 2.5.x compatible external Magnetometer I2C 3.3V interface

ArduFlyer/APM 2.5.x compatible Status LEDs for ARM and GPS


Package content:

Rctimer ArduFlyer 2.5.2 x 1

Rctimer CN06PLUS x 1

RCTimer Radio Telemetry Kit 915Mhz x 1

RCTimer Annunciator x 1

AVDome kit x 1


If you have any questions about this product, submit your questions!

Ask a question

Contact: (Can be phone, email, qq, etc.)
If you have any comments on the product or experience, please share!

Write a Review

Contact: (Can be phone, email, qq, etc.).
Powered by ShopEx v4.8.5 |Gzip disabled